Alexmos 32Bit High Power 3 Axis 20A Brushless Gimbal Controller

Posted on Leave a comment

Available soon. Final version will be black

Final version

Alexmos 32Bit High Power 3 Axis Controller - 20A
Alexmos 32Bit High Power 3 Axis Controller – 20A
Alexmos 32Bit High Power 3 Axis Controller - 20A
Alexmos 32Bit High Power 3 Axis Controller – 20A
Alexmos 32Bit High Power 3 Axis Controller - 20A
Alexmos 32Bit High Power 3 Axis Controller – 20A
Alexmos 32Bit High Power 3 Axis Controller - 20A
Alexmos 32Bit High Power 3 Axis Controller – 20A

Alexmos SimpleBGC Firmware 2.4 Released

Posted on Leave a comment

[wp_lightbox_prettyPhoto_video link=”https://www.youtube.com/watch?v=GGibOCUp_GU” description=”Alexmos SimpleBGC Firmware 2.4 Released” source=”https://aerialpixels.com/wp-content/uploads/2014/02/Alexmos-Software-2.4.jpg” title=”Alexmos SimpleBGC Firmware 2.4 Released” show_logo=”0″ show_info=”0″]

 

A new algorithm for increased reliability when motor misses steps:  PID gain is decreased, POWER is increased to restore synchronization

Alexmos SimpleBGC Firmware 2.4

 

New menu commands to turn motors ON/OFF.

Alexmos 2.4 Motor On Off Menu Button

 Follow for the PITCH+ROLL and YAW axis can be activated independently

Alexmos Firmware 2.4 New Follow Mode Options

 

New realtime visual bar to display the actual POWER level.

Realtime Visual Power Level to the motors

 

2.40b6

Firmware: SimpleBGC_2_40b6.enc.hex (86Kb 4.02.2014)

GUI (Windows, OS X, Linux): SimpleBGC_GUI_2_40.zip (5Mb 4.02.2014)
User manual: SimpleBGC_manual_2_4_eng.pdf (428Kb 2.02.2014)

  • Bug fixed: some parameters are always kept their default values regardless of GUI setting
  • A new algorithm for increased reliability when motor misses steps:  PID gain is decreased, POWER is increased to restore synchronization
  • Follow mode was completely rewritten:
    •  speed can be adjusted in wide range by the “SPEED” setting
    •  acceleration limiter is applied
    •  LPF smoothing is applied (configured in the “RC setting” tab)
    •  Follow for the axes PITCH+ROLL and YAW  can be activated independently
    •  Follow for ROLL axis may be permanently enabled or disabled regardless of camera PITCHing:  to disable completely, set “ROLL start”=90, “ROLL mix”=0, to enable set “ROLL start=0”, “ROLL mix=0”.   (Note, that proper Follow offset calibration for ROLL is required now)
  • Up to 5x more precision with the new PID (increase I-term until oscillation starts and than reduce a little back to get the maximum from it)
  • New menu commands to turn motors ON/OFF.
  • (GUI): new setting for additional POWER in case of big error (caused by missed steps).
  • (GUI): new visual bar to display the actual POWER level.
  • (GUI): new setting to enable estimation of the frame angle from motor’s poles in the Lock mode, like in the Follow mode before. Helps to increase the range of  frame angles where gimbal’s operation is stable.

 

Alexmos 3 Axis Brushless Gimbal Controller DIY Box Assembled

Posted on Leave a comment

Fully Assembled Alexmos 3 Axis DIY Box. Box comes ready to plugin. LED Status indicator and Menu Bottom Hard Wired. Option to connect an external LED and menu button in parallel.

  • Alexmos 3 Axis board – not stacked
  • Headers soldered
  • Copper High Dissipation heatsinks mounted
  • Custom 5 wire interconnect
  • 12AWG or 14AWG power leads soldered and terminated with XT60 connector (Total 5 x Pairs Inlcuded)
  • Bluetooth Module Installed
  • Board flashed with the latest firmware, default settings loaded and tested for proper operation. NOT TUNED FOR ANY CAMERA
  • Various ferrite rings will be included
  • Box will mount using standard 2 axis board mounting pattern
  • Built-in Menu Button
  • Staus/Power LED
  • Power Switch
  • Alexmos Buzzer Included

Note: The Mounting pattern is 45mm (Standard Alexmos Board Hole Patttern). The 2 boards will need to be unscrewed from the box in order to mount the box. Enough slack provided to remove to the boards. Tuning to be done using Bluetooth module. The 2 axis board will have to be removed in order to access the USB port. If direct access to USB port is needed a whole will have to be drilled. 

  • Alexmos 3 Axis Brushless Gimbal Controller Box Assembled

    Alexmos 3 Axis Brushless Gimbal Controller DIY Box Assembled

Alexmos 3 Axis Brushless Gimbal Controller Box – Fully Assembled

Posted on Leave a comment

Alexmos 3Axis DIY Box Assembled

 

Due to large amount of requests and many having issues putting the boards together, we will be releasing the current DIY Box fully assembled and soldered.

What’s included so far:

  • Alexmos 3 Axis board – not stacked
  • Copper High Dissipation heatsinks mounted
  • Custom 5 wire interconnect
  • 12AWG or 14AWG power leads soldered and terminated with XT60 connector
  • Bluetooth Module Installed
  • Board flashed with the latest firmware and tested for operation
  • Various ferrite rings will be included
  • Box will mount using standard 2 axis board mounting pattern